[please send your comments]
Q1: Which of the Following are reasons you might go into the BIOS?
Ans: verify device are connected.
make adjustments to hardware functionality
report on computer hardware
Q2: What precautions should you take to help prevent electrostatic discharge?
Ans: Use a wareless anti-static strap
Wear a fully-gronded ESD wrist strap.
Q3: What should you do before you start troubleshooting a problem?
Ans: Check whether the system is in warranty.
Q4: Why should ZIF socket T covers be replaced on system boards for returns?
Ans:To protect the socket pins.
Q5:Which innovation supersedes older BIOS in dell portable and desktop computers?
Ans:UEFI BIOS.
Q6:When replacing the USB 3.0 cable in the Precision T7600.What will need to be removed?
Ans: System Board
Q7:A desktop will not boot.The PSA/ePSA indicates that the hard drive pass checks
Which of these is the most likely explanation.
Ans: Corrupt Operating System
Hard drive connection not seated correctly
Missing operating system
Q1: Which of the Following are reasons you might go into the BIOS?
Ans: verify device are connected.
make adjustments to hardware functionality
report on computer hardware
Q2: What precautions should you take to help prevent electrostatic discharge?
Ans: Use a wareless anti-static strap
Wear a fully-gronded ESD wrist strap.
Q3: What should you do before you start troubleshooting a problem?
Ans: Check whether the system is in warranty.
Q4: Why should ZIF socket T covers be replaced on system boards for returns?
Ans:To protect the socket pins.
Q5:Which innovation supersedes older BIOS in dell portable and desktop computers?
Ans:UEFI BIOS.
Q6:When replacing the USB 3.0 cable in the Precision T7600.What will need to be removed?
Ans: System Board
Q7:A desktop will not boot.The PSA/ePSA indicates that the hard drive pass checks
Which of these is the most likely explanation.
Ans: Corrupt Operating System
Hard drive connection not seated correctly
Missing operating system
Q8: What should you do before replacing a hard drive?
Ans: Run the hard drive self-test.
Q9: Working on a desktop,you remove the system DIMMs and
switch power back on.the system does not beep.what can you conclude from this?
Ans: System Board is bad.
Q10: Which key do you press during power-on to access the bios
interface?
Ans: <F2>.
Q11: The newest Optiplex systems indicate faults by means of:
Ans: The Power Button LED.
Q12: Where will you find a BIST(built-in self-test) button on
an Optiplex or Precision computer?
Ans: On the power supply unit.
Q13: What do newer Optiplex systems use to mount fans to the
system?
Ans: Rubber Grommets instead of screws.
Q14: Working with the Precision R5500.in which first available
slot should you install the PSU?
Ans: Lowest slot.
Q15: Which of these computers have VESA mount brackets?
Ans: Optiplex 9010 A|O
Inspiron 2330
A|O
Q16: Which portfolio has a model which may be housed in the
data Center?
Ans: Precision.
Q17: You should always check the service tag to ensure that you
are servicing the right system:
Ans: True
Q18: Best practices when handling
parts(motherboards,cards,HDDs,etcJinclude:
Ans: Lifting and Holding edges and sides of part.
Right On! If I would of find this quicker I would of gotten an 100!
ReplyDeleteGreat Article .You definitely hit the key points. Mutli-media is almost everywhere from phones to netbooks to laptops to corporate PCs.
ReplyDeleteRDP Thin Client & Citrix Thin Client
Q2 is wrong. The correct answer is everything except for the wireless anti-static strap.
ReplyDeleteQ3 is wrong. It should be the one about checking the bios.
ReplyDeleteQ1: Which Product family is optimal for graphic rendering and complex data analysis?
ReplyDeleteAns: Precision
Q2: To determine if a system has a bad memory DIMM, you should:
Ans: Remove all memory modules except memory in the 1st slot.
Q3: Which checks should you perform when a faulty processor is suspected?
Ans: Thermal and Beep codes
Q4: Which of the Following are reasons you might go into the BIOS?
Ans: verify device are connected.
make adjustments to hardware functionality
report on computer hardware
Q5: What precautions should you take to help prevent electrostatic discharge?
Ans: Handle components by the edges.
Wear a fully-gronded ESD wrist strap.
Remove plastic bags, Styrofoam, and tape from work area.
Q6: What should you do before starting troubleshooting a problem?
Ans: Whenever possible, check that the system has the latest BIOS version.
Q7: Why should ZIF socket T covers be replaced on system boards for returns?
Ans: To protect the socket pins.
Q8: Which innovation supersedes older BIOS in dell portable and desktop computers?
Ans: UEFI BIOS.
Q9: When replacing the USB 3.0 cable in the Precision T7600.What will need to be removed?
Ans: System Board
Q10: A desktop will not boot.The PSA/ePSA indicates that the hard drive pass checks.
Which of these is the most likely explanation.
Ans: Corrupt Operating System
Missing operating system
Q11: What should you do before replacing a hard drive?
Ans: Run the hard drive self-test
Q12: Working on a desktop, you remove the system DIMMs and switch power back on.the system does not beep.what can you conclude from this?
Ans: System Board is bad.
Q13: Which key do you press during power-on to access the bios interface?
Ans: .
Q14: The newest Optiplex systems indicate faults by means of:
Ans: The Power Button LED.
Q15: Where will you find a BIST(built-in self-test) button on an Optiplex or Precision computer?
Ans: On the power supply unit.
Q16: What do newer Optiplex systems use to mount fans to the system?
Ans: Rubber Grommets instead of screws.
Q17: Working with the Precision R5500.in which first available slot should you install the PSU?
Ans: Lowest slot.
Q18: Which of these computers have VESA mount brackets?
Ans: Optiplex 9010 AIO
Inspiron 2330 AIO
Q19: Which portfolio has a model which may be housed in the data Center?
Ans: Precision.
Q20: You should always check the service tag to ensure that you are servicing the right system:
Ans: True
Q21: Best practices when handling parts(motherboards,cards,HDDs,etc;) include:
Ans: Lifting and Holding edges and sides of part
Witch checks should you preform when you suspect a faulty processor
Delete• Thermal and Beep Codes
Which of the following are reasons you might go into the BIOS?
• Verify Devices are connected
• Report on computer hardware
• Make adjustments to hardware functionality
What precautions should you take to help prevent electrostatic discharge?
• Use a wear a fully-grounded ESD wrist strap
• Always touch the chassis while earthed before starting work on parts
What should you do before you start troubleshooting a problem?
• Whenever possible check that the system has the latest bios
Working on a ruggedized notebook you remove the system DIMMs and switch power back on. The system does not beep. What can you conclude from this?>
• System board is bad
How is the LVDS cable secured to the LCD panel connector on a ruggedized dell notebook?
• Retainer clip
When returning a printed circuit board assembly (PCBA) to dell, which of the Following repacking steps should be taken? (Select all that apply)
• Place small parts between the upper foam covering an the box lid
• Insert the board into an ESD bag
A ruggedized notebook will not boot. The PSA/r indicates that the hard drive pass checks. Which is the most likely explanation?
• Missing operating system
• Corrupt operation system
What will leave a power supply unplugged for 2 minutes accomplish?
• Reset the power supply
Which innovation supersedes older BIOS in Dell portable and desktop computers?
• UNEFI bios
What should you do before replacing a hard drive? All that applies
• Run the hard drive self-test
When replacing a system board in a ruggedized dell notebook, what happens if you enter an incorrect service tag?
• Replacement fails and a new system board must be requested.
Bothe the latitude XFR and ATG notebooks are equipped with (all that apply)
• Hot-swappable media modules
• Dustproof keyboards and water jet resistant
• 14: HD reinforced display
•
• Reinforced HD display
• Liquid cooled processor
Where are the two keyboard captive screws located on an xfr notebook?
• Bottom bas below docking door
Which key do you press during a power-on to access the bios interface on a ruggedized dell notebook
•
Which three of these are features of the latitude XFR
• Fire resistant
• Water jet resistant
• Enhanced cooling thermal management system
• Dust tight
How do you start the PAID DIAGNOSTICS?
• Press and hold down the key, the n press the power button\
What is the first step when removing an LCD panel and dampeners from a Ruggedized Dell laptop?
• Remove the tape and disconnect the touch screen cable
When a part has a visible damaged, what should you do? All that applies
• Do not use the part and contact technical support
• Return the part to dell with a description of the damage
Best practices for LCD handling include
• Lifting/handling LCD from side/edge with both hands
How do we run a PAID LCD BIST diagnostics
• Verify the system is turned off. Press and hold down the key. Press the power button.
Thank you very much.
DeleteThanks! this helped me :D
DeleteThanks dude, you rock!
DeleteDoes anyone have the Q&A for Dell servers, Networking or any of the other Direct Tech training for 2014?
ReplyDeleteyour mom does
DeleteOh snap!
DeleteWhat Elton said.
ReplyDeletedoes anyone have the Q & A for Dell Printers?
ReplyDeleteFor anyone who wants the Q & A for Dell Printers I finally passed it and am posting it here for you. xD
ReplyDelete1: Which of the following are characteristics of our single function portfolio products?
Answer: Instant on, Faster processor, Larger cartridge
2:Which of the following are characteristics of our multi-function portfolio products?
Answer: Fast dual, All new user, more standard & max
3: Multifunction printers include a _____. These features enable the printer to function as a ______, or ______, as well as a printer while reducing overall printing costs.
Answer: Scanner Photo Scanner
4: The electronic subsystem (ESS) of the laser printer includes:
Answer: Select All Options
5: On a laser printer, poor image quality, misfeeds and jams are most commonly related to:
Answer: Physical Media Issues
6: The imaging engine (subsystem) has two functions:
Answer: True
7: A faulty HVPS or a loose connection between the HVPS and the charge roller can manifest the same symptoms as:
Answer: A failed charge Roller
8: All Laser printers contain:
Answer: All of the above
9: Symptoms of a damaged or malfunctioning drum include:
Answer: All of the Above
10: Any Residual Charge on the drum surface can:
Answer: True
11: Failure of the fuser prevents the _____ from adhering to the media.
Answer: Toner
12: What does duplexing or duplex imaging enable?
Answer: Printing on both sides of the media.
13: Do not lift greater than 60 pounds...
Answer:True
14: Do not ____ the tamper proof seal on ESD...
Answer: Break
15 Parts that are returned to Dell should be repackaged in the same manner in which they were received.
Answer: True
16 Dell workgroup laser printers have which two diagnostic modes:
Answer: Customer mode, Developer/Customer Engineer
17 WHat Checks the built-in firmware tests on Dell workgroup laser printers?
Answer: None of the above
18 Which components need to be installed in order for the manual feed test to be executed?
Answer: Components of the media path
19 When a printer is plagued with misfeeds and jams ther media needs to be checked for:
Answer: Media size, Moisture, Damage and that it lays fleet in the tray
20 Cleaning a laser printer should be a part of your routine maintenance schedule because accumulated toner can:
Answer: Adhere the media to rollers or cause rollers to fail, Land on the media as it progresses through the path
21 Worn or dirty rollers may not be able to move media through the feed path... True
22 When an image quality is completely or partially black output, what you have to do?
Answer: Check the printer cartridges, Enable the change all colors to black text smoothing
23 Noise issues can be generated from any moving parts such as:
Answer: All of the above
*Be careful! Some of my numbers were a bit funky when taking the exam. So ensure your looking at the right question when you put the answer.
question 13: false, don't lift more then 50lbs by yourself
DeleteIt's true in Question 13 - i checked
DeleteThis will only get you an 82.6 FYI
DeleteThanks.
DeleteQ13: Which key do you press during power-on to access the bios interface?
ReplyDeleteAns:
F2
DeleteDoes anyone have the questions and answers for the Dell Notebook Certification?
ReplyDeleteQ? how is the lvds cable secured to the lcd panel connector on a ruggedized dell notebook?
ReplyDeletetape I passed the test. hopefully i did it right
Deletenot one of the answers
Deletescrews
Deletescrews
DeletePlease i need this Ans for Ruggedized notebook..
ReplyDeleteQ-where are the two keyboard captive screws located on an XFR note? rear of the chassis.
Q-which three of these are features of the latitude XFR?
Q- How do you start the paid disgnostics?
Q-what is the first step when removing an LCD panel and dampeners from a ruggedized dell laptop?
Q-when a part has visible damage, whay shold u do? do not use the part and contact tech support
Q-how do u run paid lcd bist diagnostics
Q-how is the lvds cable secured to the lcd panel connector on a ruggedized dell notebook?
Q-when a part has visible damage, what should you do?
please share answers if you found them
DeleteQ-where are the two keyboard captive screws located on an XFR note? rear of the chassis.
Deleteunder the docking door
Q-which three of these are features of the latitude XFR?
14” reinforced screen
Optional resitive touch screen
Discrete graphics
Hot swappable media module options
Ip-65 (dust tight, water het resistant)
mIL-STD-461f (electromagnetic compatibility)
ul1604(fire/explosion hazard)
enhanced conductive cooling termal management system
Q- How do you start the paid disgnostics?
fn key
Q-what is the first step when removing an LCD panel and dampeners from a ruggedized dell laptop?
remove the tape and disconnect the touch screen cable
Q-when a part has visible damage, whay shold u do?
do not use the part and contact tech support
don’t use the part
Return it to dell with description
Q-how do u run paid lcd bist diagnostics
d key
Q-how is the lvds cable secured to the lcd panel connector on a ruggedized dell notebook?
retainer clips
Q-when a part has visible damage, what should you do?
do not use the part and contact tech support
don’t use the part
anyone has the server systems answers please
ReplyDeleteDoes anybody has the Server Systems Q & A ???. If so, that would be highly appreciated
ReplyDeletei'm currently doing the server cert and will upload soons as i'm done
ReplyDeleteGents here's my two cents input hope it helps:
ReplyDeleteServers
I got Pass mark by changing a few so review where I marked unsure:
Q1: In which form factor is the 12G server avail ?
Ans: Tower, Blade, Rack
Q2: Which new M-series blades are avail in M1000e ?
Ans: Full & Half
Q3: which is the embedded management feature in the 12G server line?
Ans: iDRAC7
Q4: which of the following IDRAC7 funtion levels ….?
Ans: Remote OS installation
Q5: how do you upgrade license for idrac7?
Ans: IDRAC7 portal
Q6: which of these can you do thanks to IDRAC7…?
(not sure) Ans:
Q7: What information do you need before you config. An OS with LCC…?
Ans: OS License Key , Location of OS image, desired raid config.
Q8: Which 12G storage controller is used for ext storage only?
Ans: PERC810
Q9: which of these is not supported by PERC310?
Ans: Internal Tape
Q10: Dell Open Manage Essentials is replacement for ?
Ans: ITA
Q11: Which key is for access to IDRAC7 ?
Ans:
Q12: What Funtions does LCD front Panel allow?
*Ans: Change IDRAC7 IP to DHCP , Reset IDRAC, diagnose POST
Q13: when PSU indicator is flashing amber?
Ans: PSU failsafe failure & PSU firmware updating
Q14: What’s critical to run after part replacement?
Ans: ePSA
Q15: The Select Network adaptor allows up to what speed….?
Ans: 40GbE
Q16:The flexibility of the Select Network Adaptor allows you two Config. Serves in a variety of network configurations so that they work together what is it called?
Ans: converg. Networking
Q17: you replaced a network daughter card and power on the system …?
Ans: NDC LED activity
Q18: Because of a server digital lisence what must be done when replacing a system boards?
Ans: Restore service tag
Q19:on a PE R720 & PE R720xd which cables must you check when closing the cover of the system?
(not sure) Ans:
Q20: Dell OpenManage essential allow you to?
(not sure) Ans : Discover dell server, storage … < sure about this not sure what else.
Q21: After Replacing a 12G system board what must you reconfig. In IDRAC BIOS?
Ans: The IP adresss setting
Q22: When replacing a PSU from the rear, what extra precaution must you take ?
Ans: check cable management and network cables
Q23: ReadyRail II sliding “slim” rails are now use with with all 12G rack server, Why ?
(not sure) Ans:
Q24: ePSA
Q25: although SAS connectors on 12G servers are the same as the previous generations, damage can occur while removing the connectors . what effect can this have?
Ans: loss of connectivity to the SAS devices
Q26: The DMC allows you to perform?
Ans: DELL BIOS updates, Hardware performance monitoring, deep hardware inventory & Warranty reporting
Q27: Which of the following is a controller used with M-Series only?
(not Sure) Ans:
Q11 answer is F10 dont know why it doesn't appear
ReplyDeleteAnyone who have Networking cert?...thanks in advance...
ReplyDeleteQ27 Chassis Management Controller(s)
ReplyDeleteDoes anyone have the information for the Networking portion of the Dell Certification?
ReplyDeleteDose anyone have the information for DCSE Foundation 2013 Alienware Certification and DCSE Foundation 2013 Ruggedized Certification .
ReplyDeleteGod bless you people!
ReplyDeleteanyone DCSE Foundation 2013 Alienware Certification ?
ReplyDeleteAnyone?
Deleteany answers for Networks exam
ReplyDeleteI have goen through your site, this is a good one.for more information visit Laptop Direct
ReplyDeleteDoes anyone have the answers to the DCSE Foundation 2013 PowerVault certifcation?
ReplyDeleteI do.
DeleteThis comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteAll above plus these with X in front gets an 85%
ReplyDelete6. Which of these can you do thanks to the iDrac7 LCC Platform Restore option?
X Restore the factory settings
X Backup your RAID configuration
Backup your server configuration
Backup all your data
7. Which key is for access to IDRAC7?
X F10
F11
F12
F2
19. On a PE R720 & PE R720xd which cables must you check when closing the cover of the system?
The Network Cables
X The SAS Cables
The SCSI Cables
The Power Cables
20. Dell OpenManage essential allow you to?
Platform Restore
Restore the service tag
Cluster servers together
X Hardware inventory report
X Discover dell server storage and network devices
Alert management of the box and the lower foam insert
23. ReadyRail II sliding “slim” rails are now use with with all 12G rack server, Why ?
To allow more servers to be stacked
X 12G server widths have increased
To cut down the manufacturing costs
To allow systems that support GPUs more room in the rack
27. Which of the following is a controller used with M-Series only?
SAS Controller
X Chassis Management controller
PERC H710
IDRAC7 with lifestyle controller
This is for the Dell Server test
DeleteLenovo RFSW1010EN-R1 Lenovo Idea Systems Service Training Basics - Field Service - Lenovo IdeaCentre Desktop Authorization Training
ReplyDeletehttp://www.4shared.com/office/drJekeWVce/Lenovo_RFSW1010EN-R1_Lenovo_Id.html
For anyone who wants the Q & A for Dell DCSE Foundation 2013 Alienware Certification. I just took the test and get 91%
ReplyDelete1 - Which checks should you perform when a faulty processor is suspected?
Thermal and Beep Codes
2 - What will leaving a power supply unplugged for 2 minutes accomplish?
Reset the power supply
3 - A Bios CD should be used to enter the Service Tag in which of the following instar….
Only for system which came with a BIOS CD
4 - What does a Beep code of 7 beeps indicates?
CPU failure
5 - What should you do before replacing a hard drive
Run the hard drive self-test
6 - Alien Autopsy can be used to?
View System Alerts
Run PC Backup
Run Backup & Recovery (Respawn)
7 - What Alienware solution is used for system backup and recovery?
AlienRespawn
8 - Windows recovery Environment (WinRE) in Windows 7 can be run from which of the following?
Boot menu
9 - Overclocking can be configured with which of the following?
System setup utility
10 - Pressing when powering on an Alienware notebook will lauch which of the following?
ePSA
11 - An Alienware system will not boot. The PSA/ePSA incates that the hard drive pass checks. Which of these is the most likely explanation?
Missing operation system and corrupt operation system
12 - What key is used to access the Boot Menu during POST?
F12
13 - Which of the following might be used on Alienware system to access the Bios?
F2
14 - Which of the following are reasons you might go into the BIOS?
Verify devices are connected; Report on computer hardware; Make adjustments to hardware fu.
15 - When should you wear a grounding strap?
When working inside any computer system
16 - What does a blinking power button LED indicates?
Battery status abnormal
17 - What should you do before starting troubleshooting a problem?
Whenever possible, check that the system has the latest BIOS version
18 - When returning a Printed Circuit Board Assembly (PCBA) to Dell, which of the following repack……?
Place small parts between upper foam covering and the box lid; Insert the board into an ESD bag
20 - Working on an Alienware system, you remove the system DIMMs and switch power back on. The sys….
System board is bad
21 - Which innovation supersedes older BIOS in Dell portable and desktop computer?
UEFI
22 - When replacing a system board, what happens if you enter an incorrect service tag?
Replacement fails, and a new system board must be requested
23 - The replacement for Dell 32-bit diagnostics is?
ePS
My 2 Cents
Delete24 To determinate if a system has a bad memory DIMM you should:
Remove all memory modules except memory in first slot
25 Best practice for LCD handling include:
Lifting / handling LCD from side/edge with both hands
Question 8 - Answer Boot Menu is WRONG!!!
DeleteQuestion 10 - Answer ePSA is WRONG!!!
DeleteThanks for your marvelous posting! I quite enjoyed reading it, you are a great author. I will be sure to bookmark your blog and definitely will come back from now on. I want to encourage that you continue your great job, have a nice day.
ReplyDeleteIT security certification
Does anyone know the answers to networking certification
ReplyDeleteDell Foundation Training for PowerVault Storage Solutions and Dell Training for Networking PLEASE!!! I AM STUCK.
ReplyDelete1. snapshot, virtual disk copy, remote replication (FC)
Delete2.PowerVault Tape solutions two categories, t or f? T
3.2 steps starting issue diagnostic: understand infrastructure, verify system settings not modified
4. T or F service tag and express service code used to route support calls: T
5. Need service tag to download drivers? F
6. PowerVault MD RAID controller functions: i/o ports for host, disks, enclosures, attbs to host
7. service action allowed is amber, remove expansion module? F
8.Removing controller from NX3600 NAS can cause dataloss when... LED is... blinking green
9. Never remove ML6000 Blade unles amber for 10 min? T
10. TLx000 Operator Control Panel 2 modes, user int and system driven
11. Ping behavior: helps ensure connectivity bw nics, even on same subnet could fail cuz OS
13. SEL and LC same log? separate logs
14. idrac7 trigger multiple actions for each alert? F
15.ePSA F12? F11 during boot or F10 through LC
16. OMSA enable system admins or server admins? Sys admins
17. PowerVault MD controller state? 3 possible states offline, quiesced, lockdown
18.recovery guru replace troubleshooting? F
19. PowerVault MDSM logs bundel ZIP archive of useful data? T
20.3 statements of dell lasso: raw data txt html
21.Tape drive drivers have to be installed because back up software? POST checks all hardware, T
22. ESD two guidelines, edges, before open discharge static, last place in antistatic
23.40 lbs two people? F
24.
25.var log messages for global on linux? yes
26. do not blank the tamper proof seal on ESD bag BREAK
27. replacement parts 2 prechecks: order check, then break on secure surface
asset s to get service tag
30. FC switch is heart of SAN and can be used to isolate probs on HBA and target T or F? T
31. cleaning cartridge how often? whenever
9 (real 9) Back of unit, Outlet, Strip, USB
Delete13(real 13) True
20. Stat is packaged, Company and Sites, Lasso 4.x
24. T
29. Cable, push, press
Several of these questions have changed. These answers only get you a 72. Taking it now so will be back with some of the other questions that need answers.
DeleteFollow up. Use answers to above posts with these 3 additions/corrections.
Delete8.blinking amber (Not green)
25./var/log/messages
28.asset (asset tag)
That gets you to an 80.64 (passing grade)
Got 77.41 combining all questions for PowerVault
DeleteRetest this am and passed with 96.77.
DeleteQ6 is monitoring, controlling and communicating
Q10 is User interaction and system driven
Q11 ping is Helps ensure connectivty exist between nics
Q12 When system event ocurs...SEL and LC is True
Q14 is Yes.
Q15 is F11
Q19 is F
Q20 is Dell Lasso, Includes company and site contact. Can be accessed from the BIOS
Does anyone know the answers of Dell networking certificatin
ReplyDeleteThanks!
ReplyDeleteDoes anyone have the Dell Powervault questions I;m struggling with them.
ReplyDeleteQuestion 12 which of these phrases correctly describes behaviour of of the Ping function?
Question 17
Question 20
Question 21
Question 30
Question 31
Hi,
ReplyDeleteThank you so much for sharing such a valuable and creative post.. Nice representation.. I love the way you have defined all detail regarding dell optiplex .. Nice representation... Keep posting..
plzzz give answers of Dell Wyse thin client foundations(cert id 3204)...I am struggling for its answers.plz help
ReplyDeleteDoes anybody has answers for DCSE Alienware 17 R1?
ReplyDeleteDell EqualLogic PS Series Training
ReplyDeleteEvaluation Answers:
What console or telnet/ssh command can be run to verify a disk drive fault?
Diag *-a d*
Disk zero is located where in the PS4000?
Top Row, FAR LEFT disk
PS6010 Supports how many 10 Gigabit Ports?
2
Within a single PS Series Group, Which of the following is a correct configuarion?
ALL are correct configurations
How is a faulty disk identified on the PS4000?
Red LED on the lower right corner of the disk drive
What is the maximum number of disk drives supported in the PS6500?
48
What is the maximum number of disk drives supported in the PS6000?
16
PS4000 supports how many 1 gigabit ports?
2
Once the disk has been replaced, how can you determine the disk status on the array?
By doing ALL the actions listed
PS6000 supports how many gigabit ports?
4
How many dedicated management ports are there on the PS6000 controller?
ZERO
How is a faulty disk identify on the PS6010?
Red LED on the lower right corner of the disk drive
That should get you a fat 100%
Hi, Does anyone has answer for DCSE Client Foundations 2016 (CertID 3223)?, thank you in advance.
ReplyDeleteyes i having , but i passed just 80.00%, so i mail u!
DeleteThanx for the share your data with us. We are just waiting for new data. Call us for DELL PRINTER DRIVER at Toll-free 1-888-993-6399 USA, for Dell Customer Service troubleshooting and all problems related to dell printer.
ReplyDeletehi, does any one have the answer of DCSE 1000 Enterprise Q2 Assessment 2016 (Cert ID: 3214) Exam ?
ReplyDeleteI am Waiting For DSCE 1000 Enterprise Answers
DeleteCert ID: 3214
That is outstanding Dell Printer. It can be use in Home as well as office also. We are also a Dell Service Provider and Dell Technical Support from USA. Any Dell issue like Printer, laptop, Computer, Tablet, Screen and so on. We are solve all type of Dell Issue Our Dell Printer Support Phone Number is 1-888-993-6399 at USA Toll free.
ReplyDeletePlease Upload DCSE 2000 Client 2016 (Cert ID: 3211) And
ReplyDeleteDCSE 1000 Client Foundations 2016 (Cert ID: 3223)
Answers
Yes it is good idea
DeleteWonderful blog & good post.Its really helpful for me, awaiting for more new post. Keep Blogging!
ReplyDelete123.hp.com/setup 5810
This comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteplease upload DCSE 2000 EqualLogic PS Series Break/Fix (Cert ID: 3130) answers thanks
ReplyDeleteThis is very helpful and saves me soo much time
ReplyDeletePlease upload DCSE 2000 storage Foundations CERT ID 3167
ReplyDeleteplease upload cert ID 3199
ReplyDeletePlease update Client Foundations 2016 (Cert ID: 3223)
ReplyDeleteplzzz give answers of Dell Wyse thin client foundations(cert id 3204)...I am struggling for its answers.plz help
ReplyDeleteplzzz give answers of Dell Wyse thin client foundations(cert id 3204)...I am struggling for its answers.plz help
ReplyDeleteThanks for sharing this wonderful blog. Canon Printer Toll Free Number
ReplyDeletedell technical support,dell printer support,dell support,dell help,dell tech support,dell customer support,
ReplyDeletedell customer service,dell helpline,dell customer number
dell printer support
Does anybody have these:
ReplyDeleteDCSE 1000 Client Foundations 2016 (Cert ID: 3223) (1.0)
DCSE 1000 Client Q3 Assessment 2016 (Cert ID: 3225) (1.0)
DCSE 1000 Client Q4 Assessments 2016 (Cert ID: 3227) (1.0.0)
DCSE 1000 Enterprise Foundations 2017 (Cert ID: 3226) (1.0.0)
DCSE 1000 Enterprise Foundations (DCSE ID: 3202) (1.0.0)
DCSE 1000 Enterprise Q4 Assessment (Cert ID: 3207)
DCSE 1000 Enterprise Q4 Assessments 2016 (Cert ID: 3231) (1.0.0)
DCSE 2000 Client 2016 (Cert ID: 3211)
DCSE 2000 Client Q4 Assessments 2016 (Cert ID: 3228) (1.0.0)
DCSE 2000 Printer Q3 Assessment 2016 (Cert ID: 3224) (1.0)
DCSE 2000 Printers 2016 (Cert ID: 3212)
DCSE 2000 Wyse Thin Client Foundations 2015 (Cert ID: 3204)
DCSE 2000 Wyse Thin Client Q4 Assessments 2016 (Cert ID: 3229) (1.0.0)
Thanks!
Hello
ReplyDeleteCan someone help me with the DES-1D11?
You’re providing service useful information for printer online service,
ReplyDeleteIt is very useful for printer users. we are very happy to read the blog.
DELL Customer Services |
DELL Printer Support